ULTRA FL 00623
- ExxonMobil Chemical
Request Sample
Request Documents
Ask Question
Share
You`ll need an account to perform this action. Don't worry. It's free!
Sign Up
You`ll need an account to compare products. Don't worry. It's free!
Sign Up
FL 00623 is a good coextrusion partner in extrusion coating, blown and cast film. Excellent sealing material with a very low seal initiation temperature.
Maximum processing temperature is 230°C (428°F).
You`ll need an account to add a review. Don't worry. It's free!
Sign Up
You`ll need to place an order to add a review. Don't worry. It's easy!
Documents
Technical data sheetProduct Details
- Manufacturer
ExxonMobil Chemical
- Plastic Generic Family
Polyethylene (PE)
Properties
Physical Properties
| Title | Value | Unit | Method | Additional Information | Property Notes |
|---|---|---|---|---|---|
| Density | 0.947 | gm/cm³ | ASTM D1505 | - | - |
| Melt Flow Index | 5.5 | gm/10 min | ASTM D1238 | (190°C / 21.6 Kg) | - |
| Durometer Hardness | 87 | Shore A | ASTM D2240 | 15 sec | - |
| Durometer Hardness | 30 | Shore D | ASTM D2240 | 15 sec | - |
Mechanical Properties
| Title | Value | Unit | Method | Additional Information | Property Notes |
|---|---|---|---|---|---|
| Tensile Modulus | 29 | MPa | ASTM D638 | (0.20 in/min(5.0mm/min)) | - |
| Tensile strength at Break | 19 | MPa | ASTM D638 | (20 in/min(510mm/min)) | - |
| Elongation @ Break | 860 | % | ASTM D638 | (20 in/min(510mm/min)) | - |
Thermal properties
| Title | Value | Unit | Method | Additional Information | Property Notes |
|---|---|---|---|---|---|
| VICAT Softening Point | 51 | °C | ASTM D1525 | - | - |
| Peak Melting Temperature | 80 | °C | EXXONMOBIL Method | - | - |
Legal Statement:
Contact your ExxonMobil Chemical Customer Service Representative for potential food contact application compliance (e.g. FDA, EU, HPFB).
This product is not intended for use in medical applications and should not be used in any such applications.
Processing Statement:
Molded properties were measured on 2 mm (78.7 mil) thick compression molded plaques prepared based on ASTM D4703 Procedure C (Tensile ASTM D638 : Type IV dumbbell, Hardness ASTM
D2240 : 3 plied up disks) and 4 mm (157 mil) for VICAT.
Notes:
Typical properties: these are not to be construed as specifications.
Product may not be available in one or more countries in the identified Availability regions. Please contact your Sales Representative for complete Country Availability.
ASTM D638 : Type IV dumbbell, Hardness ASTM D2240 : 3 plied up disks) and 4 mm (157 mil) for VICAT
| Plastic Generic Family | Polyethylene (PE) |
|---|---|
| Description | Legal Statement: Contact your ExxonMobil Chemical Customer Service Representative for potential food contact application compliance (e.g. FDA, EU, HPFB).
This product is not intended for use in medical applications and should not be used in any such applications.
Processing Statement:
Molded properties were measured on 2 mm (78.7 mil) thick compression molded plaques prepared based on ASTM D4703 Procedure C (Tensile ASTM D638 : Type IV dumbbell, Hardness ASTM D2240 : 3 plied up disks) and 4 mm (157 mil) for VICAT.
Notes: Typical properties: these are not to be construed as specifications. Product may not be available in one or more countries in the identified Availability regions. Please contact your Sales Representative for complete Country Availability.
ASTM D638 : Type IV dumbbell, Hardness ASTM D2240 : 3 plied up disks) and 4 mm (157 mil) for VICAT |
- Product Review
- Seller Review